Calle Colombia nº 22 (local izda), 28016 MADRID | Teléfonos: 913504965 - 913503130
HORARIO: Lunes a Viernes 10:30-14:00 y 17:00-20:00. Sábados 10:00-14:00
URL: http://www.studio-22.com | E-MAIL: studio22@studio-22.com
 
SOBRE LA TIENDA ALTA FIDELIDAD CINE EN CASA AUDIO PERSONAL ACÚSTICA
NOTICIAS MARCAS Y PRODUCTOS ALTAVOCES PULSAR AUDIO REPORTAJES DE FERIAS CÓMO CONTACTAR
NOVEDADES CATÁLOGO
CÓMO COMPRAR
DISPONIBILIDAD
GASTOS DE ENVÍO
FINANCIACIÓN
FORMULARIOS DE PEDIDO








 



 






 






Hazte fan en Facebook

Síguenos en Twitter

Datos studio-22.com

· Tamaño web:
40,5 GB
· Nº de subpáginas: 12.211
· Nº de imágenes: 93.023
· Nº de archivos PDF: 5.864

Portada > Amplificadores integrados > Puresound > Puresound A30
Puresound A30
Más información en http://www.puresound.info/
AMPLIFICADOR INTEGRADO ESTÉREO A VÁLVULAS (4 x 6550) CON 2 x 30 W
Descarga del catálogo en .PDF

The Pure Sound A30 amplifier was developed to meet the demand for an affordable Class A amplifier that would be compatible with all types of loudspeakers. The A30 is a line level integrated design that allows for the selection of up to 3 different source components and control of the volume by a high quality ALPS Blue Velvet potentiometer. Class A operation was chosen because it gives lower distortion and a more relaxing, natural sound.

The amplifier uses the very robust Electro Harmonix 6550 output valves in an Ultra Linear Push Pull configuration. This arrangement gives a combination of power and clarity that is difficult to beat. The amplifier uses an Auto Bias system, which means that replacement output valves should be fitted as matched pairs. There will be no need to reset or monitor bias conditions.

Very high quality components are used throughout including selected carbon film resistors and SCR polypropylene capacitors. The power supply makes use of twin valve rectifiers and choke smoothing.

The output can be configured for use with 4 or 8 ohm loudspeakers. The Pure Sound A30 may also be used as a very high quality stereo power amplifier if the volume control is turned up fully. When partnered with appropriate ancillary equipment the A30 is capable of very satisfying performance

Why this amplifier? Why now?

With the recent interest in lower powered Single Ended triode amplifiers has come the realization that to get the best from these, the speakers used have to be both sensitive and quite large to give truly satisfying results. There are also not that many good, high sensitivity (>97 dB/W) designs available at any price never mind at price levels the majority of music lovers can afford. However, there are some very good loudspeakers currently being made with sensitivities between 88 and 94dB/W. These are sufficiently revealing to make the virtues of simple, high quality amplification readily apparent, although in most cases the output of a typical single ended amplifier is insufficient to give the scale and drama many types of music demand.

A good amplifier with 25 -30 watts of output power is more than enough to drive this type of loudspeaker to sensible levels even in quite a large room. For circuit simplicity, a valve amplifier is preferable. Recently, there has been an increase in the number of relatively affordable valve amplifiers made in China. Many of these are compromised by the quality of their transformers, components, layout and because they operate in Class AB or B to give a higher power specification. They often also use a lot of negative feedback in an attempt to compensate for these shortcomings with a consequential impact on clarity and low frequency control.

For some 10 years there has been a lack of affordable Class A valve amplifiers. The Pure Sound A30 operates fully in Class A up to its rated output so it does not change character at any signal level. There is none of the distortion caused by output devices switching on and off and therefore no requirement for excessive feedback to correct for it. The 6550 valves supplied are the extremely robust Russian Electro-Harmonix variety and are quite content with dissipating the power required to maintain Class A operation up to 30 Watts. The valve rectifiers used keep the high voltage power supply clear of the noise that can be introduced by silicon rectifiers. A substantial choke is also incorporated to keep the power supply impedance low. The output transformers also give extremely wide bandwidth allowing very solid low frequency performance as well as exceptional reproduction of timbre.

These design features combined with the use of high quality passive components, octal based input and driver triodes and an elegant but simple internal layout results in an amplifier which sets a new benchmark for performance, build quality and value.

...
PVP recomendado:
2.195 €
IVA incluido

  Producto en stock propio. Disponible en tienda física o para envío inmediato


Pulsar en la foto para ampliar

Pulsar en la foto para ampliar

Pulsar en la foto para ampliar

Pulsar en la foto para ampliar


Especificaciones:

Potencia de salida 30W por canal (acoplamiento ultralineal) / 18W por canal (acoplamiento triodo)
Respuesta de frecuencia 20Hz - 20KHz (-0,025 a -0,3 dB)
THD 0.3%
Impedancia de entrada 100 kohmios
Relación señal/ruido 88 dB
Sensibilidad de entrada 100 mV para 0 dB
Consumo de corriente 260 W
Peso neto 28 kg
Dimensiones 436 (ancho) x 190 mm (alto) x 360 mm (fondo)
Entradas 3 x Nivel de línea
Conectores de salida 4 y 8 ohmios
Válvulas implementadas 4 x 6550
2 x 5Z4P
2 x 6N9P (6SL7)
2 x 6N8P (6SN7)

 
Studio 22

   Calle Colombia nº 22 (local izda), 28016 MADRID | Teléfonos: 913504965 - 913503130
   HORARIO: Lunes a Viernes 10:30-14:00 y 17:00-20:00. Sábados 10:00-14:00
   URL: http://www.studio-22.com | E-MAIL:

 

 

Volver arriba